am

scan ip-addr [bssid ]

test ip-addr

auto-device-creation

start interval phy-type {80211a|80211g}

stop

create-device

ap phy-type {80211a|80211g} [bssid ] [mac ]

client phy-type {80211a|80211g} [bssid ] [mac ]

ev-gen event_id trap_id [ADDITIONAL_INFO | ADDRESS_TYPE |

AP_CHANNEL | AP_LOCATION |

AP_MAC_ADDRESS | AP_RADIO_NUM |

ASSOCIATION_TYPE | CONF_LEVEL |

FRAME_TYPE | INTERFERING_AP_INFO_URL | MATCHED_IP | MATCHED_MAC |

NODE_MAC | RECEIVER_MAC | ROGUE_INFO_URL | SIGNATURE_NAME | SNR

SOURCE_MAC | SPOOFED_FRAME_TYPE | TARGET_AP_BSSID | TARGET_AP_SSID | TRANSMITTER_MAC ]

suspect-rap bssid match-type match-method

wired-mac

add {bssid mac |enet-mac mac |prop-wm mac |system-gw-wm mac |system-wm mac }

remove {bssid mac |enet-mac mac |prop-wm mac |system-gw-wm mac |system-wm mac }

Description

Thescansub-command enables channel scanning for the specified air monitor. In addition, thetestsub-command enables the client to test an air monitor. These commands are intended to be used with an AP that is configured as an air monitor.

Parameter	Description
scan	Enable or disable channel scan.
ip-addr	IP address of the air monitor to be scanned.
	Channel to which the scanning is tuned. Set to 0 to enable scanning of all channels.
bssid	BSSID of the air monitor.
test	Enables the client to test an air monitor.
ip-addr	IP address of the air monitor.
auto-device-creation	Sets the AP mode to add a monitored device and client at every interval. start stop Intervals are written as time in seconds.
interval	Sets the interval in seconds at which the new AP and client devices are added.
phy-type {80211a\|80211g}	设置设备的乐队。 80211a foraband 80211g forgband
create-device {ap \| client}	Creates an AP or client device. ap client
phy-type {80211a \| 80211g}	指定了band for the device. 80211a 80211g
bssid	指定了bssid of the new device
mac	指定了wired-mac address of the new device
ev-gen	Create an IDS event from the AP.
event_id	指定了event id to generate for the event.
trap_id	指定了trap id to generate or use 65535 if there are no traps. The various trap IDs are explained here: ADDITIONAL_INFO—Additional information for syslog ADDRESS_TYPE—Address type (an integer because it is enum) AP_CHANNEL—Detecting AP channel or target channel AP_LOCATION—Detecting AP Name AP_MAC_ADDRESS—Detecting AP MAC AP_RADIO_NUM—Detecting AP Radio ASSOCIATION_TYPE—Association Type ex. Association To Rogue CONF_LEVEL—Confidence level of suspected rogue (5-100) FRAME_TYPE—Frame type (an integer because it is enum) INTERFERING_AP_INFO_URL—URL MATCHED_IP—Matched IP for classification MATCHED_MAC—Matched MAC for classification NODE_MAC—Node MAC RECEIVER_MAC—Receiver MAC ROGUE_INFO_URL—URL SIGNATURE_NAME—Name of signature matched SNR—Signal-to-Noise Ratio SOURCE_MAC—Source MAC SPOOFED_FRAME_TYPE—Spoofed Frame type ( EAP Success) TARGET_AP_BSSID—Target AP BSSID TARGET_AP_SSID—Target AP SSID TRANSMITTER_MAC—Transmitter MAC
suspect-rap	Test the suspect remote AP feature.
bssid	指定了BSSID of monitored AP.
match-type	指定了match type.
match-method	指定了match method.
wired-mac {add \| remove}	Tests the rogue AP classification feature. Specifies the wired MAC table.
bssid mac	Specifies BSSID of monitored AP and wired-MAC address.
enet-mac mac	MAC address of ENET interface of AP and wired-MAC address.
prop-wm mac	指定了propagate wired-MAC
system-gw-wm mac	指定了system gateway MAC.
system-wm mac	指定了system wired-MAC.

Example

The following command sets the air monitor to scan all channels:

(host) (config) #am scan 10.1.1.244 0

Command History

Release	Modification
ArubaOS8.0.0.0	Command introduced.

Command Information

Platforms	License	Command Mode
All platforms	Base operating system.	Enable mode onMobility Conductor.