ap wired-port-profile

ap wired-port-profile {default | }

aaa-profile{默认| <配置文件名称>}

authentication-timeout

auto-recovery-enable

auto-recovery-interval

bridge-role

clone {default | }

enet-link-profile

lldp-profile {default | }

loop-detection-interval

loop-protect-enable

portfast

portfast-trunk

rap-backup

shutdown

spanning-tree

storm-control-broadcast

storm-control-broadcast-threshold

wired-ap-profile

Description

This command configures a wired port profile. This command is only applicable to APs with Ethernet ports. Issue this command to enable or disable the wired port, define an AAA profile for wired port devices, and associate the port with an ethernet link profile that defines its speed and duplex values.

Parameter	Description
ap wired-port-profile	Name of this instance of the profile. The name must be 1–63 characters.
aaa-profile	Name of a AAA profile to be used by devices connecting to the wired port of the AP.
authentication-timeout	Authentication timeout value, in seconds, for devices connecting the wired port of the AP. Range:1-65535 Default:5
auto-recovery-enable	Enables automatic recovery of the port in the AP that is shut down because of loop protection. After the automatic recovery, if the loop re-occurs, then the port is shutdown again Disabled
auto-recovery-interval	Specify the time, in seconds, to automatically recover the port in the AP that is shut down because of loop protection. Range:30-43200 Default:300
bridge-role	Role that is assigned to a user if split-tunnel authentication fails.
clone	Create a new AP wired port profile based upon the values of an existing profile.
enet-link-profile	Specify an Ethernet link profile to be used by devices associated with this wired port profile. The Ethernet link profile defines the duplex value and speed to be used by the port.
lldp-profile	Specify an LLDP profile to be used by devices associated with this wired port profile. The LLDP profile specifies the type-length-value (TLV) elements to be sent in LLDP PDUs.
loop-detection-interval	Specify the time, in seconds, to send loop detection packets on the ports of an AP. Range:1-10 Default:2
loop-protect-enable	Enables loop protection on the ports of an AP. Default:Disabled
no	Negates any defined parameter
portfast	Enables portfast for AP wired ports. Spanning tree must be enabled before this command can be used.
portfast-trunk	Spanning tree must be enabled before this command can be used.
rap-backup	Use the`rap-backup`parameter to use the wired port on a Remote AP for local connectivity and troubleshooting when the AP cannot reach themanaged device. If the AP is not connected to themanaged device, no firewall policies will be applied when this option is enabled. (The AAA profile will be applied when the AP is connected tomanaged device).
shutdown	Disable the wired AP port.
spanning-tree	Enables the spanning-tree protocol.
storm-control-broadcast	Enables the broadcast storm control. When this parameter is enabled, if the AP detects a loop on one of its Ethernet port, it shuts down the Ethernet port. This prevents the AP from receiving or sending any frames.
storm-control-broadcast-threshold	Specify the broadcast packets per second on each Ethernet port of an AP before the Ethernet port is shut down. Default:2000
wired-ap-profile	Name of a wired AP profile to be used by devices connecting the wired port of the AP. The wired AP profile defines the forwarding mode and switchport values used by the port.

Example

The following command defines a AAA profile for wired port devices:

(host)[mynode] (config) #ap wired-port-profile wiredport1

(host)[mynode] (AP wired port profile"wiredport1") #aaa-profile default-open

(host)[mynode] (AP wired port profile"wiredport1") #authentication-timeout 30

(host)[mynode] (AP wired port profile"wiredport1") #wired-ap-profile wiredap1

Command History

Release	Modification
ArubaOS8.3.0.0	The following parameters were introduced: `auto-recovery-enable` `auto-recovery-interval` `loop-detection-interval` `loop-protect-enable` `storm-control-broadcast` `storm-control-broadcast-threshold`
ArubaOS8.0.0.0	Command introduced.

Release

Modification

ArubaOS8.3.0.0

The following parameters were introduced:

auto-recovery-enable

auto-recovery-interval

loop-detection-interval

loop-protect-enable

storm-control-broadcast

storm-control-broadcast-threshold

ArubaOS8.0.0.0

Command introduced.

Command Information

Platforms	地方政府投资公司ense	Command Mode
All platforms	Base operating system, except for noted parameters.	Config mode onMobility Conductor.