显示AP Active AP-Name
Description
This command shows data for a specified AP name.
Example
The following example shows data for a specified AP name:
(host) [mynode] #show ap active ap-name AP-205
Active AP Table
---------------
Name Group IP Address AP Type Flags Uptime Outer IP Cluster Role Active Clients Standby Clients
Radio 0 Band Ch/EIRP/MaxEIRP/Clients Radio 1 Band Ch/EIRP/MaxEIRP/Clients Radio 2 Band Ch/EIRP/MaxEIRP/Clients
---- ----- ---------- ------- ----- ------ -------- ------------ -------------- ---------------
------------------------------------ ------------------------------------ ------------------------------------
标志：1 = 802.1x身份验证的AP;2 =使用IKE版本2;
A = Enet1 in active/standby mode; B = Battery Boost On; C = Cellular;
d = disconn。额外的电话；E =有线AP启用;F = AP失败802.1x身份验证；
H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh;
N = 802.11b protection disabled; P = PPPOE; R = Remote AP;
S = AP连接为待机；X =维护模式；
a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP;
i = Provisioned as Indoor; o = Provisioned as Outdoor;
p = Restriction mode in POE-AF/AT;r = 802.11r Enabled; f = No Spectrum FFT support;
Q = DFS CAC timer running; T = Flex Radio Mode is 2.4GHz+5GHz; t = Tri-Radio Mode Enabled;
U = Flex Radio Mode is 5GHz; V = Flex Radio Mode is 2.4GHz; e = custom EST cert; W = Dual 5GHz Mode Enabled; 4 = Using WiFi Uplink
Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.
Channel flags: +/- = 40 MHz, E = 80 MHz, S = 160 MHz, E+E = 80 + 80 MHz (i.e. 36E+149E)
Cluster Role: U = UAC, A = AAC, SU = Standby UAC , SA = Standby AAC
Num APs:0
|
In releases prior toArubaOS8.3.0.0,该命令的输出包括ed 2.4 GHz and 5 GHz as output parameters. InArubaOS8.3.0.0, these output parameters are modified to display the radio IDs, bands, EIRP, Maximum EIRP, and number of clients. |
此命令的输出包括以下信息：
Column |
Description |
Name |
AP的名称 |
Group |
The AP is associated with this AP group. |
IP address |
AP的IP地址，点虚线小数格式。 |
AP Type |
AP model type. |
Flags |
This column displays any flags for this AP. The list of flag abbreviations is also included in the output of the 1 = 802.1X authenticated AP 2 =使用IKE版本2; 4 = Using Wi-Fi Uplink A = Enet1 in active/standby mode B = Battery Boost On C = Cellular; d = disconn。额外的电话 E = Wired AP enabled F = AP failed 802.1X authentication H = Hotspot Enabled K = 802.11K Enabled L = Client Balancing Enabled M = Mesh N = 802.11b protection disabled P = PPPOE R = Remote AP S = AP connected as standby X = Maintenance Mode a = Reduce ARP packets in the air d = drop mcast/bcast u = Custom-Cert RAP i = Provisioned as indoor o = Provisioned as outdoor p = Restriction mode in POE-AF/AT r = 802.11r Enabled t=Tri-radio mode enabled Q = DFS CAC timer running T = Flex Radio Mode is 2.4GHz+5GHz U = Flex Radio Mode is 5GHz V = Flex Radio Mode is 2.4GHz W = Dual 5 GHz Mode Enabled |
Uptime |
Number of hours, minutes and seconds since the lastMobility Conductorreboot or bootstrap, in the formathours:minutes:seconds. |
Outer IP |
The outer IP address of a远程APis used to establish an IPsec VPN tunnel to the terminatingMobility Conductor. The RAP acquires an outer IP address from the locally connected network, usually via DHCP. (A远程APis typically behind a NAT device whose public IP is seen as the outer IP for the远程AP). |
Radio 0 Band Ch/EIRP/MaxEIRP/Clients |
Radio ID, channel, EIRP, Maximum EIRP, and the number of clients using Radio 0. |
Radio 1 Band Ch/EIRP/MaxEIRP/Clients |
Radio ID, channel, EIRP, Maximum EIRP, and the number of clients using Radio 1. |
Radio 2 Band Ch/EIRP/MaxEIRP/Clients |
Radio ID, channel, EIRP, Maximum EIRP, and the number of clients using Radio 2. |
Related Commands
命令 |
Description |
This command configures an AP system profile. |
|
This command configures a Wi-Fi uplink profile. |
命令历史记录
Release |
Modification |
ArubaOS8.7.0.0 |
The output parametersandwill include the following details: : Indicates mesh enabled radio of a mesh portal. The mesh point radio that has a parent link. The mesh point radio without a parent link. |
ArubaOS8.6.0.0 |
Two new output parametersandwere introduced. |
ArubaOS8.5.0.0 |
A new flag,was introduced to indicate Wi-Fi uplink. |
ArubaOS8.3.0.0 |
New flags,,,, andwere introduced. In addition, the output parameters for this command were modified to show the radio ID (that is, Radio 0 and Radio 1), radio band, and the debug details such as APs' operation mode for the dual 5GHz mode settings. |
ArubaOS8.0.0.0 |
命令introduced. |
命令Information
Platforms |
License |
命令Mode |
All platforms |
Base operating system. |
Config or Enable mode onMobility Conductor. |
