show ap active ip6-addr
Description
This command shows data of an AP for specified IPv6 address.
Example
The following example shows data of an AP for specified IPv6 address:
(host) [mynode] #show ap active ip6-addr 2001:08:85a3:0000:0000
Active AP Table
---------------
Name Group IP Address AP Type Flags Uptime Outer IP Cluster Role Active Clients Standby Clients
Radio 0 Band Ch/EIRP/MaxEIRP/Clients Radio 1 Band Ch/EIRP/MaxEIRP/Clients Radio 2 Band Ch/EIRP/MaxEIRP/Clients
---- ----- ---------- ------- ----- ------ -------- ------------ -------------- ---------------
------------------------------------ ------------------------------------ ------------------------------------
Flags: 1 = 802.1x authenticated AP; 2 = Using IKE version 2;
A = Enet1 in active/standby mode; B = Battery Boost On; C = Cellular;
D = Disconn. Extra Calls On; E = Wired AP enabled; F = AP failed 802.1x authentication;
H = Hotspot Enabled; K = 802.11K Enabled; L = Client Balancing Enabled; M = Mesh;
N = 802.11b protection disabled; P = PPPOE; R = Remote AP;
年代= AP connected as standby; X = Maintenance Mode;
a = Reduce ARP packets in the air; d = Drop Mcast/Bcast On; u = Custom-Cert RAP;
i = Provisioned as Indoor; o = Provisioned as Outdoor;
p = Restriction mode in POE-AF/AT;r = 802.11r Enabled; f = No Spectrum FFT support;
Q = DFS CAC timer running; T = Flex Radio Mode is 2.4GHz+5GHz; t = Tri-Radio Mode Enabled;
U = Flex Radio Mode is 5GHz; V = Flex Radio Mode is 2.4GHz; e = custom EST cert; W = Dual 5GHz Mode Enabled; 4 = Using WiFi Uplink
Channel followed by "*" indicates channel selected due to unsupported configured channel.
"Spectrum" followed by "^" indicates Local Spectrum Override in effect.
Channel flags: +/- = 40 MHz, E = 80 MHz, S = 160 MHz, E+E = 80 + 80 MHz (i.e. 36E+149E)
Cluster Role: U = UAC, A = AAC, SU = Standby UAC , SA = Standby AAC
Num APs:0
|
In releases prior toArubaOS8.3.0.0,该命令的输出包括ed 2.4 GHz and 5 GHz as output parameters. InArubaOS8.3.0.0, these output parameters are modified to display the radio IDs, bands, EIRP, Maximum EIRP, and number of clients. |
The output of this command includes the following information:
Column |
Description |
Name |
Name of an AP |
Group |
The AP is associated with this AP group. |
IP地址 |
IP地址of the AP, in dotted decimal format. |
AP Type |
AP model type. |
Flags |
This column displays any flags for this AP. The list of flag abbreviations is also included in the output of the 1 = 802.1X authenticated AP 2 = Using IKE version 2; 4 = Using Wi-Fi Uplink A = Enet1 in active/standby mode B = Battery Boost On C = Cellular; D = Disconn. Extra Calls On E = Wired AP enabled F = AP failed 802.1X authentication H = Hotspot Enabled K = 802.11K Enabled L = Client Balancing Enabled M = Mesh N = 802.11b protection disabled P = PPPOE R = Remote AP 年代= AP connected as standby X = Maintenance Mode a = Reduce ARP packets in the air d = Drop Mcast/Bcast On u = Custom-Cert RAP i = Provisioned as indoor o = Provisioned as outdoor p = Restriction mode in POE-AF/AT r = 802.11r Enabled t=Tri-radio mode enabled Q = DFS CAC timer running T = Flex Radio Mode is 2.4GHz+5GHz U = Flex Radio Mode is 5GHz V = Flex Radio Mode is 2.4GHz W = Dual 5 GHz Mode Enabled |
Uptime |
Number of hours, minutes and seconds since the lastMobility Conductorreboot or bootstrap, in the formathours:minutes:seconds. |
Outer IP |
The outer IP address of aRemote APis used to establish an IPsec VPN tunnel to the terminatingMobility Conductor. The RAP acquires an outer IP address from the locally connected network, usually via DHCP. (ARemote APis typically behind a NAT device whose public IP is seen as the outer IP for theRemote AP). |
Radio 0 Band Ch/EIRP/MaxEIRP/Clients |
Radio ID, channel, EIRP, Maximum EIRP, and the number of clients using Radio 0. |
Radio 1 Band Ch/EIRP/MaxEIRP/Clients |
Radio ID, channel, EIRP, Maximum EIRP, and the number of clients using Radio 1. |
电台2乐队Ch /附近/ MaxEIRP /客户 |
Radio ID, channel, EIRP, Maximum EIRP, and the number of clients using Radio 2. |
Related Commands
Command |
Description |
This command configures an AP system profile. |
|
This command configures a Wi-Fi uplink profile. |
Command History
Release |
Modification |
ArubaOS8.7.0.0 |
The output parameters : Indicates mesh enabled radio of a mesh portal. The mesh point radio that has a parent link. The mesh point radio without a parent link. |
ArubaOS8.6.0.0 |
Two new output parametersandwere introduced. |
ArubaOS8.5.0.0 |
A new flag,was introduced to indicate Wi-Fi uplink. |
ArubaOS8.3.0.0 |
New flags,,,, andwere introduced. In addition, the output parameters for this command were modified to show the radio ID (that is, Radio 0 and Radio 1), radio band, and the debug details such as APs' operation mode for the dual 5GHz mode settings. |
ArubaOS8.0.0.0 |
Command introduced. |
Command Information
Platforms |
License |
Command Mode |
All platforms |
Base operating system. |
Config or Enable mode onMobility Conductor. |
