show ap debug bss-config

show ap debug bss-config [ap-name |bssid ||essid |ip-addr |ip6-addr |port /]

Description

Shows the configuration for each BSSID of an AP. This information can be used to troubleshoot problems on an AP.

Parameter

Description

ap-name

Filter the AP Config table by AP name.

bssid

Filter the AP Config table by BSSID. The Basic Service Set Identifier (BSSID) is usually the AP’s MAC address.

essid

Filter the AP Config table by ESSID. An Extended Service Set Identifier (ESSID) is a alphanumeric name that uniquely identifies a wireless network. If the name includes spaces, you must enclose the ESSID in quotation marks.

ip-addr

Filter the AP Config table by IP address by entering an IP address in dotted-decimal format.

ip6-addr

Filter the AP Config table by IP address by entering an IPv6 IP address in dotted-decimal format.

port /

Filter the AP Config table by port and slot numbers. The slot and port numbers should be separated by a forward slash (/).

Examples

下面的例子显示了美联社配置table for a specific BSSID.

(host) #show ap debug bss-config

ArubaAP Config Table

---------------------

bss ess vlan ip phy type fw-mode max-cl rates tx-rates preamble mtu --- ---- ---- -- --- ---- ------- ----- ----- -------- -------- ---

status wmm

------ ---

00:1a:1e:11:24:c2 cera2 66 10.6.1.203 g-HT ap tunnel 64 0x3 0xfff enable 0 enable enable

00:1a:1e:8d:5b:11 wpa2 65 10.6.1.198 a-HT ap tunnel 20 0x150 0xff0 - 0 enable enable

00:0b:86:9b:e5:60 guest 63 10.6.14.79 g ap tunnel 20 0x2 0x3fe enable 0 enable enable

00:1a:1e:97:e5:41 voip 66 10.6.1.199 g-HT ap tunnel 20 0xc 0x14c enable 0 enable enable

00:1a:1e:11:74:a1 voip 66 10.6.1.197 g-HT ap tunnel 20 0xc 0x14c enable 0 enable enable

00:1a:1e:11:5f:11 wpa2 65 10.6.1.200 a-HT ap tunnel 20 0x150 0xff0 - 0 enable enable

下面的例子显示了美联社配置table for a specific BSSID ( ArubaOS8.9.0.0or later versions).

(host) [mynode] (config) #show ap debug bss-config Aruba AP Config Table --------------------- bss ess vlan ip band/ht-mode/bandwidth type fw-mode max-cl rates tx-rates preamble status wmm mtu flags --- --- ---- -- ---------------------- ---- ------- ------ ----- -------- -------- ------ --- --- ----- 84:d4:7e:e6:17:50 9@hhm-535-rtp 0 1.1.1.4 5GHz/VHT/80MHz ap tunnel 64 0x150 0xff0 - enable enable 0 D cc:88:c7:41:64:60 8@hhm-635-psk 0 10.65.36.220 6GHz/HE/160MHz ap tunnel 64 0x150 0xff0 enable enable enable 0 DTWx3 Channel followed by "*" indicates channel selected due to unsupported configured channel. "Spectrum" followed by "^" indicates Local Spectrum Override in effect. Num APs:2 Num Associations:0 Flags: a = Airslice policy; A = Airslice app monitoring; c = MBO Cellular Data Capable BSS; d = Deferred Delete Pending; D = VLAN Discovered;

E = Enhanced-open BSS without transition mode; I = Imminent VAP Down; K = 802.11K Enabled; m = Agile Multiband (MBO) BSS; M = WPA3-SAE mixed mode BSS;

o = Enhanced-open transition mode open BSS; O = Enhanced-open BSS with transition mode; r = 802.11r Enabled; t = Broadcast TWT Enabled;

T = Individual TWT Enabled; W = 802.11W Enabled; x = MBSSID Tx BSS; 3 = WPA3 BSS;

The output of this command includes the following information:

Column

Description

bss

Basic Service Set (BSS) identifier, which is usually the AP’s MAC address.

ess

Extended Service Set (ESS) identifier; a user-defined name for a wireless network.

vlan

The BSSID’s VLAN number.

IP

The AP’s IP address.

phy

( For versions prior toArubaOS8.9.0.0)

One of the following 802.11 types

a

a-HT (high-throughput)

g

g-HT (high-throughput)

band/ht-mode/bandwidth

( For versions prior toArubaOS8.9.0.0)

The AP radio type displayed by radio band/throughput type/channel bandwidth. Possible values for each type are as follows:

band—2.4GHz,5GHz, or6GHz

ht-mode—HT,VHT, orHE

bandwidth—20MHz,40MHz,80MHz,80+80MHz, or160MHz

type

This column shows if the BSSID is for an access point (ap) or an air monitor (am).

fw-mode

The configured forward mode for the AP’s virtual AP profile.

bridge: Bridge locally

split-tunnel: Tunnel tocontrolleror NAT locally

tunnel: Tunnel tocontroller

max-cl

的最大数量的客户owed for this BSSID.

序言

Shows if short preambles are enabled for 802.11b/g radios. Network performance may be higher when short preamble is enabled. In mixed radio environments, some 802.11b wireless client stations may experience difficulty associating with the AP using a short preamble.

MTU

Maximum Transmission Unit (MTU) size, in bytes. This value describes the greatest amount of data that can be transferred in one physical frame.

status

Shows if this BSSID is enabled or disabled.

wmm

Shows if the BSSID has enabled or disabled WMM, also known as IEEE 802.11e

Enhanced Distribution Coordination Function (EDCF) WMM provides prioritization of specific traffic relative to other traffic in the network.

Related Commands

Command

Description

show ap bss-table

This command shows the Basic Service Set (BSS) table of an AP.

Command History

Release

Modification

ArubaOS8.9.0.0

The following changes were introduced:

Replacedphywithband/ht-mode/bandwidthparameter in the command output.

Replacedgandawith2.4GHzand5GHzvalues in the command output.

Added6GHzvalue in the command output for Wi-Fi 6E APs.

Addedxflag in the command output parameter for Wi-Fi 6E APs.

ArubaOS8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable or Config mode onMobility Conductor.