显示AP显示器调试

Shows the maximum classification delay that was observed in monitored APs and clients, the number of Unclassified Device messages that were sent to the WMS, and the number of monitored APs/clients that were present in those messages. This parameter also shows the number of monitored APs/clients that were created and removed by the AP. This information is captured on an hourly basis for the last 24 hours.

NOTE:The maximum delay for clients is not displayed if theunclass_sta_updateparameter is not enabled.

Shows the configuration received by the AP for each profile.

Shows general AP status information and the maximum classification delay that was observed in monitored APs and clients, in theWLAN接口选项。

NOTE:The maximum delay for clients is not displayed if theunclass_sta_updateparameter is not enabled.

显示具有特定名称的AM的数据。

我与一个特定的BSSID显示数据。证ID is usually the AP’s MAC address.

Show data for an AM with a specific IP address by entering its IPv4 address in dotted-decimal format.

Show data for an AM with a specific IP address by entering its IPv6 address in dotted-decimal format.

显示空气监视器主动扫描配置。

Show the Air Monitor radio configuration parameters, as defined in the AM’s 802.11a, 802.11b, or high-throughput radio profiles.

Show an Air Monitor’s system configuration settings, as defined in it’s AP System profile.

Show an Air Monitor’s ARM settings, as defined in its current ARM profile

Show an Air Monitor Event Thresholds settings, as defined in its current RF Event Thresholds profile

Show an Air Monitor IDS DoS settings, as defined in its current IDS DoS profile.

Show an Air Monitor IDS General Configuration settings, as defined in its IDS General profile.

Show an Air Monitor IDS Impersonation Configuration settings, as defined in its IDS Impersonation profile.

显示Air Monitor IDS签名匹配配置设置，如其IDS签名匹配配置文件中所定义

Show an Air Monitor IDS Unauthorized Device configuration settings, as defined in its IDS Unauthorized Device profile.

Show an Air Monitor’s interference configuration settings, as defined in its current RF Optimization profile.

Show an Air Monitor’s Regulatory Domain configuration settings, as defined in its Regulatory Domain profile.

BSSID for the AP. This is usually the AP’s MAC address.

Indicates whether or not if active scanning is enabled on this AP.

Indicates whether the AP radio is currently enabled or disabled.

This parameter displays one of the following options to show the AP is configured.

树液: Default AP setting.

am: AP is configured as an Air Monitor.

m-portal: AP is configured as a Mesh portal.

m-point: AP is configured as a Mesh point.

airmatch-am: AP is configured in AP monitoring mode.

此参数显示以下选项之一，以显示无线电的当前任务：

scan:据美联社扫描其他渠道。

调谐: AP is tuned on one channel.

定位: AP has been asked to locate a specific AP or client.

pcap:美联社enabled with the Packet Capture feature.

The radio channel currently used by an AP’s WLAN interface.

接口上看到的数据包数量。

MAC address for the AP’s wired interface.

The AP’s IP address.

IP address for the AP’s gateway.

MAC address for the AP’s gateway.

Shows if the interface is currently enabled or disabled.

在AP的有线接口上看到的数据包数。

该接口的有线MAC表中的MAC地址数。

该接口的有线MAC表中的MAC地址数。

Number VLAN-tagged packets sent to that interface.

The VLAN ID for the packets sent to that interface.

Number of packets read by the AP since it was last reset.

Number of bytes read by the AP since it was last reset.

Number of interrupts from the AP’s driver.

Number of times excessive traffic has filled the AP’s buffers.

Maximum throughput rate seen on the interface, in packets per second.

Current throughput rate seen on the interface, in packets per second.

Maximum interrupt rate seen on the interface, in interrupts per second.

在界面上看到的当前中断速率，每秒中断。

Number of seconds since the AP was last reset.

AP的IP地址managed device

AP的IP地址移动导体.

AP model type.

The AP’s country code. Valid radio channels for your wireless network are based on your country code. If you change the AP’s country code, the valid channels will be reset to the defaults for the new country.

Number of other APs monitored by this AP.

Number of clients and APs seen by this AP.

Number of potential APs; APs which have transmitted a beacon, but have not yet been registered.

Number of potential stations; AP has seen a MAC address from the station but hasn’t yet received traffic from it.

Number of channel entries in the channel table.

Number of different message types seen on the interface.

(For internal use only)

Indicates if the AP communicates to the wms process on移动导体或者amanaged device.

enabled：与之交流移动导体.

disabled：与managed deviceonly.

If the AP is collecting statistics, this value is the interval in seconds in which the AP sends statistics to the WMS process.

Interval, in milliseconds, that the AP sends RSSI updates to the WMS process.

Number of控制器此AP可以访问的。如果值为1，则AP可以访问移动导体或者amanaged device. If the value is 2, the AP has access to移动导体和amanaged device.

如果启用，AP将收集统计信息以发送到WMS流程。

BSSID of the radio.

Indicates whether thecontrollertype is掌握(移动导体) orlocal(managed device).

Ifup, the AP can reach themanaged device. Ifdown, the AP cannot reach themanaged device.

The time the AP last registered with the WMS process.

Number of times the AP has registered with the WMS process.

The last timer tick time the AP updated the WMS process.

Interval between the last update and the next scheduled update.

Number of updates sent to the WMS process.

Number of timer ticks since the AP received an acknowledgment from the WMS process.

Type of RTLS server used by the AP, such as MMS or Aeroscout.

RTLS服务器的IP地址。

Port used by the RTLS server.

速率在几秒钟内将RTLS消息发送到服务器。

Indicates if the server is active on the AP.

Displays whether tag reporting is enabled or not.

Displays MAC OUI of the tags that are forwarded to the server.

Displays the cumulative count of the tag reports sent to server.

Displays whether station reporting is enabled or not.

Displays whether unassociated stations are included in station reporting or not.

Displays cumulative count of station reports sent to server.