show ap mesh active [
Description
This command shows active mesh cluster APs currently registered on thisMobility Conductor.
Parameter |
Description |
Name of a mesh cluster profile. |
|
page |
Limit the output of this command to a specific number of entries by entering the number of entries you want to display. |
start |
开始选择显示网格APs的指数index number by entering the index number of the AP at which command output should start. |
Example
The following example displays a list of all active mesh points and mesh portals
(host)[mynode] #show ap mesh active
Mesh Cluster Name: mesh-515
---------------------------
Name Group IP Address AP Type Uptime Mesh Role MTU Enet Ports Parent #Children Radio0 Band/Ch/EIRP/MaxEIRP Radio1 Band/Ch/EIRP/MaxEIRP Radio2 Band/Ch/EIRP/MaxEIRP
---- ----- ---------- ------- ------ --------- --- ---------- ------ --------- --------------------------- --------------------------- ---------------------------
ap225 mesh-515 172.16.1.6 225 2d:17h:40m:1s Point Off/Off ap505 1 802.11a/36E/15.0/30.2 802.11g/1/15.0/25.0
ap345 mesh-515 172.16.1.4 345 2d:14h:25m:8s Point Off/Off ap505 0 802.11a/149E/15.0/29.7 802.11a/36E/15.0/25.2
ap375网- 515 172.16.1.115 375 2d:17h:36m:26s Point Off/Off ap225 0 802.11a/149E/15.0/35.6 802.11g/1/15.0/29.7
ap505 mesh-515 172.16.1.108 505 2d:13h:56m:36s Portal 1578 - - 2 802.11a/36E/15.0/29.5
Total APs :4
Starting fromArubaOS8.7.0.0, thecommand displays the above output only when mesh enabled radios are present. Else, the output will be displayed as following:
(host) [ mynode] #show ap mesh active
Total APs :5
The following example displays a list of all active mesh points and mesh portals for AP-635 access point
(host) [mynode] #show ap mesh active Mesh Cluster Name: jiajunname ----------------------------- Name Group IP Address AP Type Uptime Mesh Role MTU Enet Ports Parent #Children Radio0 Band/Ch/EIRP/MaxEIRP Radio1 Band/Ch/EIRP/MaxEIRP Radio2 Band/Ch/EIRP/MaxEIRP ---- ----- ---------- ------- ------ --------- --- ---------- ------ --------- --------------------------- --------------------------- --------------------------- ap635-3 mesh6xx 10.10.117.253 635 22h:45m:36s Portal 1500 -/Off - 1 6GHz/169S/20.0/21.5 ap635-4 mesh6xx 10.10.117.252 635 22h:33m:46s Point Off/Bridge ap635-3 0 6GHz/169S/20.0/21.5 Total APs :2
The output of this command includes the following information:
Column |
Description |
Name |
Name of an AP. |
Group |
AP group which includes the specified AP. |
IP Address |
IP address of the AP. |
AP type |
The AP model type. |
Uptime |
Number of hours, minutes and seconds since the lastMobility Conductorreboot or bootstrap, in the formathours:minutes:seconds. |
Mesh Role |
An AP operating as a mesh node can have one of two roles: mesh portal or mesh point. |
MTU |
MTU size, in bytes. This value describes the greatest amount of data that can be transferred in one physical frame. |
Enet Ports |
Shows one of the following current modes of each wired interface: Bridge: 802.11 frames are bridged into the local Ethernet LAN. Tunnel: 802.11 frames are tunneled to theMobility Conductorusing GRE. Split-tunnel: 802.11 frames are either bridged into the local Ethernet LAN or tunneled to theMobility Conductor, depending upon their destination. Off: Interface is not available for serving clients. If an AP has only one wired interface, the output of this command will display a dash (-) for the unavailable port. |
Parent |
If the AP is operating as a mesh point, this parameter displays the name of its parent mesh portal. Mesh portals will display a dash (-). |
#Children |
If the AP is operating as a mesh portal, this parameter shows the number of mesh point children associated with that mesh portal. |
乐队/ Ch /附近/ MaxEIRP |
The RF band in which the AP should operate (aorg)/radio channel used by the AP/current EIRP /maximum EIRP. For Wi-Fi 6E APs inArubaOS8.9.0.0 or later versions, the RF band displays one of the following values:
|
Related Commands
Command |
Description |
This command configures a mesh radio profile used by mesh nodes. |
Command History
Release |
Modification |
ArubaOS8.9.0.0 |
The command output was modified to display the RF bands as2.4 GHz,5 GHz, or6 GHz. |
ArubaOS8.7.0.0 |
This command displays a detailed output of all parameters only if mesh -enabled radios are configured. |
ArubaOS8.0.0.0 |
Command introduced. |
Command Information
Platforms |
License |
Command Mode |
All platforms |
This show command is available in the base operating system. Commands to configure the secure enterprise mesh solution for outdoor APs require the Outdoor Mesh license. |
Enable or Config mode onmanaged devices. |
