show ap mesh topology [long] [page
Description
This command shows the mesh topology tree.
Parameter |
Description |
long |
Include the names of a mesh portal’s children in the output of this command. |
page |
Limit the output of this command to a specific number of entries by entering the number of entries you want to display. |
start |
Start displaying the mesh topology tree at a chosen index number by entering the index number of the AP at which command output should start. |
Examples
An(N)in theMesh Rolecolumn indicates the node is 11N capable. An(N)beside the parent name in theParentcolumn indicates that the mesh node’s the parent is also 11N capable.
(Aruba9012_DA_90_B0) [mynode] # show ap mesh topology Mesh Cluster Name: jiajunname ----------------------------- Name State IP Address Switch IP Mesh Role Radio BSSID Parent Path Cost Node Cost Link Cost Hop Count RSSI Rate Tx/Rx Last Update Uplink Age #Children ---- ----- ---------- --------- --------- ----- ----- ------ --------- --------- --------- --------- ---- ---------- ----------- ---------- --------- ap635-3 ACTV 10.10.117.253 10.65.255.117 Portal (HE) 2 cc:88:c7:41:3d:30 - 0 1 0 0 - - 52s 22h:37m:11s 1 ap635-4 ACTV 10.10.117.252 10.65.255.117 Point (HE) 2 cc:88:c7:41:2c:e0 ap635-3 1 0 0 1 48 2401/0 3m:6s 22h:20m:30s 0 Total APs :2 (R): Recovery AP. (N): 11N Enabled. (AC): 11AC Enabled. (AD): 11AD Enabled. (HE): 11AX Enabled. For Portals 'Uplink Age' equals uptime. ACTV: Active on controller, REPL: Replicated on controller.
The output of this command includes the following information:
Column |
Description |
Name |
Name of the mesh node. |
State |
State of the mesh node. |
IP Address |
IP address of the mesh node. |
Switch IP |
IP address of thecontroller. |
Mesh Role |
An AP operating as a mesh node can have one of two roles: mesh portal or mesh point. |
Radio |
Mesh radio number of the AP. |
BSSID |
BSSID for the AP. This is usually the AP’s MAC address. |
Parent |
If the AP is operating as a mesh point, this parameter displays the name of its parent mesh portal. |
Path Cost |
A relative measure of the quality of the path from the AP to thecontroller. A lower number indicates a better quality path, where a higher number indicates a less favorable path (e.g, a path which may be longer or more congested than a path with a lower value.) For a mesh point, the path cost is the sum of the (parent path cost) + (the parent node cost) + (the link cost). |
Node Cost |
A relative measure of the quality of the node, where a lower number of is more favorable than a higher number. This cost is related to the number of children on the specified node. |
Link Cost |
A relative measure of the quality of the link. For example, a more congested link will have a higher link cost than a similar, less-congested link. |
Hop Count |
Number of hops to the mesh portal. |
RSSI |
The RSSI value displayed in the output of this command represents signal strength as a signal to noise ratio. For example, a value of 30 would indicate that the power of the received signal is 30 dBm above the signal noise threshold. |
Rate Tx/Rx |
Mbps的速度,网point transmits and receives at on its uplink. Note that the rate information is only as current as indicated in theLast Update列。 |
Last Update |
Time elapsed since the mesh node last updated its statistics. |
Uplink Age |
Time elapsed since the mesh node became active in the mesh topology. |
#Children |
Number of children associated with a parent mesh point. |
Related Commands
Command |
Description |
This command configures a mesh radio profile used by mesh nodes. |
Command History
Release |
Modification |
ArubaOS8.7.0.0 |
The output was modified to include the |
ArubaOS8.0.0.0 |
Command introduced. |
Command Information
Platforms |
License |
Command Mode |
All platforms |
Base operating system. |
Enable mode onMobility Conductor. |
