show ap remote bss-table

show ap remote bss-table [ap-name ] [bssid ] [ip-addr ] [ip6-addr ]

Description

This command shows BSSIDs of all APs registered on themanaged device. The optional output modifiers | begin , | exclude, and | include help you display those lines that begin, include, exclude, respectively, the line expression given in the CLI command. The | redirect-output modifier helps you redirect the command output.

Parameter

Description

ap-name

Shows BSSIDs of all APs registered on themanaged devicefiltered by AP name.

bssid

Shows BSSIDs of all APs registered on themanaged devicefiltered by BSSID.

ip-addr

Shows BSSIDs of all APs registered on themanaged devicefiltered by IP address.

ip6-addr

Shows BSSIDs of all APs registered on themanaged devicefiltered by IPv6 address.

Example

The following example shows the BSSID of an AP registered on themanaged device ( For versions prior toArubaOS8.9.0.0).

(host) [mynode] #show ap remote bss-table ap-name ap-205 Aruba AP BSS Table ------------------ bss ess port ip phy --- --- ---- -- --- 40:e3:d6:76:19:70 aruba-ap ?/? 191.191.191.252 a-VHT 40:e3:d6:76:19:71 guestthistime ?/? 191.191.191.252 a-VHT 40:e3:d6:76:19:60 ?/? 191.191.191.252 g-HT type ch/EIRP/max-EIRP cur-cl ap name in-t(s) tot-t ---- ---------------- ------ ------- ------- ----- ap 149E/12/24 0 ap-205 0 19d:13h:46m:14s ap 149E/12/24 0 ap-205 0 19d:13h:46m:14s am ?/?/? 0 ap-205 0 19d:13h:46m:13s Channel followed by "*" indicates channel selected due to unsupported configured channel. "Spectrum" followed by "^" indicates Local Spectrum Override in effect. Num APs:3 Num Associations:0

The following example shows the BSSID of a Wi-Fi 6E AP registered on themanaged device ( ArubaOS8.9.0.0or later versions).

(host) [mynode] #show ap remote bss-table ap-name hhm-635 Aruba AP BSS Table ------------------ bss ess port ip band/ht-mode/bandwidth ch/EIRP/max-EIRP type cur-cl ap name in-t(s) tot-t flags --- --- ---- -- ---------------------- ---------------- ---- ------ ------- ------- ----- ----- cc:88:c7:41:64:60 8@hhm-635-psk ?/? 10.65.36.220 6GHz/HE/160MHz 37S/15.0/21.8 ap 0 hhm-635 0 20d:12h:34m:1s TWx3 Channel followed by "*" indicates channel selected due to unsupported configured channel. "Spectrum" followed by "^" indicates Local Spectrum Override in effect. Num APs:1 Num Associations:0 Flags: a = Airslice policy; A = Airslice app monitoring; c = MBO Cellular Data Capable BSS; d = Deferred Delete Pending; D = VLAN Discovered;

E = Enhanced-open BSS without transition mode; I = Imminent VAP Down; K = 802.11K Enabled; m = Agile Multiband (MBO) BSS; M = WPA3-SAE mixed mode BSS;

o = Enhanced-open transition mode open BSS; O = Enhanced-open BSS with transition mode; r = 802.11r Enabled; t = Broadcast TWT Enabled;

T = Individual TWT Enabled; W = 802.11W Enabled; x = MBSSID Tx BSS; 3 = WPA3 BSS;

The output of this command includes the following information:

Column

Description

bss

The AP Basic Service Set Identifier (BSSID). This is usually the MAC address of the AP

ess

The AP Extended Service Set Identifier (ESSID).

port

The slot and port used by thecontroller, in the format //.

ip

IP address of an AP.

phy

( For versions prior toArubaOS8.9.0.0)

The radio’s PHY type. Possible values are 802.11a, 802.11a-HT-40, 802.11b or 802.11g, 802.11b or 802.11g-HT-20.

band/ht-mode/bandwidth

( ArubaOS8.9.0.0or later versions)

The AP radio type displayed as radio band/throughput type/channel bandwidth. Possible values for each type are as follows:

  • band—2.4GHz,5GHz, or6GHz
  • ht-mode—HT,VHT, orHE
  • bandwidth—20MHz,40MHz,80MHz,80 + 80 mhz, or160MHz

ch/EIRP/max-EIRP

Radio channel used by the AP/current effective Isotropic Radiated Power (EIRP) /maximum EIRP.

类型

Shows whether the AP is working as an access point (AP) or air monitor (AM).

cur-cl

Current number of clients on the AP.

ap name

Name of the AP.

in-t(s)

Number of seconds that an AP has been inactive.

tot-t

An AP’s total active time, in seconds.

flags

The type of flags available for the AP.

Command History

Release

Modification

ArubaOS8.9.0.0

The command output was modified to include the following:

Replacedphyparameter withband/ht-mode/bandwidth.

Addedxand3flags.

ArubaOS8.2.0.0

Theip6-addrparameter was added.

ArubaOS8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable mode onMobility Conductor.