show ap system-profile

For dual-band radios, this parameter displays the RF band in which the AP should operate:

• g= 2.4 GHz
• a= 5 GHz

Displays the AP behavior when a firmware assert is detected.

Scanning band for multiple RF radios.

• g= 2.4 GHz
• a= 5 GHz
• all= Radio scans both bands. This is the default setting.

Native VLAN for bridge mode virtual APs (frames on the native VLAN are not tagged with 802.1q tags).

Displays if the WIDS aggregate MPDU optimization is enabled or disabled.

Interval between heartbeat messages between a remote or campus AP and its associatedmanaged device. An increase in the heartbeat interval increases the time it will take for an AP to detect the loss in connectivity to themanaged device, but can reduce Internet bandwidth consumed by a remote AP.

This parameter shows the ACL applied on the uplink of a remote AP.

DNS name used by the corporate network.

SNMP system contact information.

Displays the LED operating mode for indoor 802.11n APs. LEDs display as usual in the defaultnormaloperating mode, but are all turned off inoffmode.

不启用时,auto-turn-off函数work. This is applicable only for APs with a single LEDs, that includeAP-228,AP-274,AP-275,AP-277,AP-365,AP-367,AP-318,AP-374,AP-375,AP-377, andAP-387access points.

Level of Driver log prints sent to syslog server.

Level of Driver log prints sent to AP console.

Maximum Transmission Unit (MTU) size, in bytes. This value describes the greatest amount of data that can be transferred in one physical frame.

The IP address of the local management switch (LMS)—theArubamanaged devicewhich is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network.

NOTE:如果the LMS-IP is blank, the access point will remain on themanaged devicethat it finds using methods like DNS or DHCP. If an IP address is configured for the LMS IP parameter, the AP will be immediately redirected to themanaged deviceat that address.

For networks with multiplemanaged devices, this parameter displays the IP address of a backup to the IP address specified with the lms-ip parameter.

For IPv6 networks with multiplemanaged devices,this parameterspecifies the IPv6 address of the local management switch (LMS)—theArubamanaged device—which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network. This can be the IP address of themanaged deviceorMobility Conductor.

In multi-controllerIPv6 networks, this parameter specifies the IPv6 address of a backup to the IPv6 address specified with theLMS IPv6setting.

When this parameter is enabled, the local management switch automatically reverts to the primary LMS IP address when it becomes available.

Time, in seconds, that the primary LMS must be available before an AP returns to that LMS after failover. Therap-dhcp-server-vlanVLAN ID of the remote AP DHCP server is used if themanaged deviceis unavailable. This VLAN enables the DHCP server on the AP (also known as the remote AP DHCP server VLAN). If you enter the native VLAN ID, the DHCP server is unavailable.

The interval at which an application level ping is sent to a primary controller to check the reachability. Applicable only for RAPs.

NOTE:如果this parameter is changed, the UDP session timeout should be set accordingly on an intermediate router. The preferred timeout value islms-ping-intervalplus 30 seconds.

VLAN ID of the remote AP DHCP server used if themanaged deviceis unavailable. This VLAN enables the DHCP server on the AP (also known as the remote AP DHCP server VLAN).

IP address used as the DHCP server identifier.

IP address of the DNS server.

IP address for the default DHCP router.

This parameter defines the starting IP address in the DHCP pool for remote APs.

This parameter defines the last IP address in the DHCP pool for remote APs.

Configures a DHCP pool for remote APs. This is the netmask used for the DHCP pool.

This is the total reserved uplink bandwidth (in kilobits per second).

Session ACLs with uplink bandwidth reservation in kilobits per second. You can specify up to three session ACLs to reserve uplink bandwidth. The sum of the three uplink bandwidths should not exceed therap-bw-totalvalue.

Shows if Remote-AP Local Network Access is enabled or disabled. By enabling this option, the clients that are connected to a remote AP can communicate.

NOTE:By default, the Remote-AP Local Network Access will be disabled.

The mode for flexible radio.

The mode for dual 5 GHz APs.

The mode for split 5 GHz APs.

Displays the activation status of the Intelligent Power Monitoring (IPM) system.

Number of consecutive missed heartbeats on a GRE tunnel (heartbeats are sent once per second on each tunnel) before an AP rebootstraps. On themanaged device, the GRE tunnel timeout is 1.5 x bootstrap-threshold; the tunnel is torn down after this number of seconds of inactivity on the tunnel.

This parameter applies only to remote APs. Double encryption is used for traffic to and from a wireless client that is connected to a tunneled SSID. When enabled, all traffic is re-encrypted in the IPsec tunnel. When disabled, the wireless frame is only encapsulated inside the IPsec tunnel.

(For debugging purposes.) Displays the server to receive the core dump generated if an AP process crashes.

DSCP value of AP heartbeats (0–63).

Shows if Maintenance mode is enabled or disabled. If enabled, APs stop flooding unnecessary traps and syslog messages to the NMS or network operations centers when deploying, maintaining, or upgrading the network. Themanaged devicestill generates debug syslog messages if debug logging is enabled.

Maximum number of times to retry AP-generated requests, including keepalive messages. After the maximum number of retries, the AP either tries the IP address specified by the bkup-lms-ip (if configured) or reboots.

Interval, in seconds, between the first and second retries of AP-generated requests. If the configured interval is less than 30 seconds, the interval for subsequent retries is increased up to 30 seconds.

The number of times the AP will attempt to recreate an IPsec tunnel withMobility Conductorbefore the AP will reboot. A value of 0 disables the reboot.

This parameter contains the following information, separated by colons:

• IPv4 or IPv6 address of an AeroScout real-time asset location (RTLS) server to which locations report are sent.
• Port number: Port number on the AeroScout server to which location reports are sent.
• Include-unassoc-sta: Specifies whether to include unassociated stations when sending station reports. Unassociated stations are stations that are not associated to any AP

Default:Disabled

This parameter contains the following information, separated by colons.

• IPv4 or IPv6 address of the RTLS server to which the AP sends RFID tag information.
• Number of the RTLS server port to which the AP sends RFID tag information.
• Shared secret key for the server.
• Frequency at which packets are sent to the server, in seconds.

Displays the status of USB port on various AP platforms that have external USB ports. Listed below are the power modes:

• auto: Detect USB power mode automatically.
• disable: Disable USB power.
• enable: Enable USB power.

NOTE:This parameter can be configured only onAP-214,AP-215,AP-224,AP-225,AP-205H,AP-303H,AP-304,AP-305,AP-314,AP-315,AP-324,AP-325,AP-334,AP-335,AP-344,AP-345,AP-203R, andAP-203RPaccess points only.

Reports whether telnet access to the AP is enabled or disabled.

如果the system profile is enabled, the AP console accesses using a backup ESSID.

This parameter allows AP console access using a backup ESSID, allowing users to access an AP console after the AP has disconnected from themanaged device. When the AP advertises a backup ESSID in either static or dynamic mode, an user is able to access and debug the AP remotely through a virtual AP. This feature is disabled by default.

Displays the URL of the Meridian server to which the Bluetooth Low Energy (BLE) sends monitoring data.

Displays the BLE endpoint authorization token. This token is unique for each deployment.

Displays the BLE operation mode of the AP.

Displays the amount of time the AP needs to keep the Ethernet link of the wired port in down state after failover to backup cluster or fallback to primary cluster.

NOTE:The port bounce feature is disabled when the value is 0.