show ap spectrum channel-summary

show ap spectrum channel-summary {ap-name | ip-addr | ip6-addr } [freq-band {2.4ghz | 5ghz| 6ghz}]

Description

This command displays a summary of the 802.11a or 802.11g channels seen by a spectrum monitor.

Parameter	Description
ap-name	Name of the spectrum monitor for which you want to view spectrum information.
ip-addr	IP address of the spectrum monitor for which you want to view spectrum information.
ip6-addr	IPv6 address of the spectrum monitor for which you want to view spectrum information.
freq-band {2.4ghz \| 5ghz} ( For versions prior toArubaOS8.9.0.0)	View information for a specific radio type, either 2.4 GHz or 5 GHz.
freq-band {2.4ghz \| 5ghz \| 6ghz} ( ForArubaOS8.9.0.0or later versions)	View information for a specific radio type, either 2.4 GHz, 5 GHz, or 6 GHz. NOTE:The 6ghz sub-parameter is applicable to Wi-Fi 6E APs only.

The output of the table can display data aggregate data for each channel seen by the spectrum monitor radio, including the maximum AP power, interference, and the Signal-to-Noise-and-Interference Ratio (SNIR).

SNIR is the ratio of signal strength to the combined levels of interference and noise on that channel. This value is calculated by determining the maximum noise-floor and interference-signal levels, and then calculating how strong the desired signal is above this maximum.

A hybrid AP on a 20 MHz channel will see 40 MHz Wi-Fi data as non- Wi-Fi data.

Example

The output of the example below shows information for 802.11a radio channels seen by the spectrum monitorap999.

(host) [mynode] #show ap spectrum channel-summary ap-name ap999 freq-band 5ghz

Channel Summary Table

---------------------

Channel KnownAPs UnknownAPs Util(%) MaxAPSignal(dBm) MaxInterference(dBm) SNIR(dB)

------- -------- ---------- ------- ---------------- -------------------- -------

149 69 0 5 -39 -69 30

153 20 0 100 -42 -60 18

157年560 6 -53 -59 6

161 54 0 4 -43 -71 28

165 32 0 3 -27 -70 43

149+ 69 0 100 -39 -60 21

157+ 20 0 6 -43 -59 16

The output of this command includes the following information:

Column	Description
Channel	An 802.11a or 802.11g radio channel.
Known APs	Number of valid APs identified on the radio channel.
UnKnown APs	Number of invalid or rogue APs identified on the radio channel.
Channel Util (%)	Percentage of the channel currently in use.
Max AP Signal (dBm)	Signal strength of the AP that has the maximum signal strength on a channel.
Max Interference(dBm)	Signal strength of the non- Wi-Fi device that has the highest signal strength.
SNIR (db)	The ratio of signal strength to the combined levels of interference and noise on that channel. This value is calculated by determining the maximum noise-floor and interference-signal levels, and then calculating how strong the desired signal is above this maximum.

Related Commands

Command	Description
ap spectrum local-override	Converts an AP or AM into a spectrum monitor by adding it to the spectrum local-override list.
rf dot11a-radio-profile mode spectrum-mode	Sets an 802.11a radio so that the device operates as a spectrum monitor and can send spectrum analysis data to a desktop or laptop client.

Command History

Release	Modification
ArubaOS8.9.0.0	The`6ghz`sub-parameter was introduced for`freq-band`parameter. (ForArubaOS8.9.0.0 or later versions)
ArubaOS8.0.0.0	Command introduced.

Command Information

平台	许可证	Command Mode
All platforms.	Base operating system.	Enable or Config mode on themanaged deviceorcontrollerwhere the AP terminates.