show ap spectrum client-list

show ap spectrum client-list {ap-name | ip-addr | ip6-addr } [ap-bssid | channel | essid | freq-band {2.4ghz | 5ghz} | limit | mac | or | page | sort | start ]

Description

This command shows details for clients seen by a specified spectrum monitor.

Parameter

Description

ap-name

Name of the spectrum monitor for which you want to view spectrum information.

ip-addr

IP address of the spectrum monitor for which you want to view spectrum information.

ip6-addr

IPv6 address of the spectrum monitor for which you want to view spectrum information.

ap-bssid

View information for a client with a specific BSSID.

band

View information for specific radio band. The possible values are 2.4ghz, 5ghz, or 6ghz.

channel

view information for clients on a specific radio channel.

essid

View information for clients using a specific ESSID.

mac

View information for a client with a specific MAC address.

or

Use this parameter to display information that meets either or two criteria, such as a specified ESSID or channel.

page

Enter a number from 10–100 (inclusive) to specify the number of entries that should appear in each page of the output for this command. For example, if the output of this command has 100 entries and you select a page value of 20, the output will appear in 5 pages each with 20 entries. If you selected a page value of 10, the output would appear in 10 pages with 10 entries.

sort

Sort the output by the specified data column.

start

Start displaying the output at specific spectrum index value.

Example

下面的例子表明,光谱模拟torap999sees eight different clients on channel 149. The output in the example below has been divided into two tables to better fit this document. In theArubaOSCLI, the output appears as a single, long table.

(host) [mynode] #show ap spectrum client-list ap-name ap999 channel 149

Spectrum Client Table

---------------------

mac bssid essid spectrum-id channel phy-type

--- ----- ----- ----------- ------- --------

00:14:a4:d1:34:63 00:24:6c:80:48:79 ethersphere-wpa2 14 149 80211a

00:19:7d:3a:96:d9 00:24:6c:80:7b:c9 ethersphere-wpa2 198 149 80211a

00:16:cf:af:3e:e1 00:24:6c:80:48:79 ethersphere-wpa2 80 149 80211a

00:1c:26:5b:a7:ac 00:24:6c:81:8b:19 ethersphere-wpa2 125 149 80211a

00:21:6b:c6:b2:12 00:24:6c:80:48:79 ethersphere-wpa2 118 149 80211a-HT-40

00:21:6a:9c:0e:36 00:24:6c:81:8b:19 ethersphere-wpa2 121 149 80211a

00:21:6a:51:e4:30 00:1a:1e:87:c1:91 ethersphere-wpa2 164 149 80211a-HT-40

00:24:d6:65:a9:e6 00:24:6c:80:48:7a ethersphere-voip 222 149 80211a-HT-40

signal(dBm) add-time last-seen

--------------- -------- -----------

-71 2010-05-17 09:53:47 2010-05-17 12:36:54

-66 2010-05-17 12:01:01 2010-05-17 12:36:42

-74 2010-05-17 09:54:59 2010-05-17 12:35:55

-79 2010-05-17 10:23:29 2010-05-17 12:37:28

-66 2010-05-17 10:17:05 2010-05-17 12:31:58

-72 2010-05-17 10:20:05 2010-05-17 12:37:30

-63 2010-05-17 11:07:21 2010-05-17 12:29:01

-69 2010-05-17 12:37:25 2010-05-17 12:37:25

start:0

Length:8

Total:8

The output of this command includes the following information:

Column

Description

mac

客户机的MAC地址。

bssid

Basic Service Set Identifier for a client. This is usually the device’s MAC address.

essid

Extended service set identifier that names a wireless network.

spectrum-id

Identifier assigned to the client by the spectrum monitor.

chan

Radio channel used by the BSSID.

phy-type

( For versions prior toArubaOS8.9.0.0)

Radio phy type. Possible types include:

  • 802.11a
  • 802.11a-HT-40
  • 802.11b/g
  • 802.11b/g-HT-20

band

( ForArubaOS8.9.0.0or later versions)

Radio band type. Possible types include:

  • 2.4ghz
  • 5ghz
  • 6 ghz (Wi-Fi 6E APs)

signal(dBm)

Client signal strength, in dBm.

add-time

Time when the client was first detected by the spectrum monitor.

last-seen

Time when the spectrum monitor last detected that the client was active.

Related Commands

Command

Description

ap spectrum local-override

Converts an AP or AM into a spectrum monitor by adding it to the spectrum local-override list.

rf dot11a-radio-profilemodespectrum-mode

Sets an 802.11a radio so that the device operates as a spectrum monitor and can send spectrum analysis data to a desktop or laptop client.

rf dot11g-radio-profilemodespectrum-mode

Sets an 802.11g radio so that the device operates as a spectrum monitor and can send spectrum analysis data to a desktop or laptop client.

Command History

Release

Modification

ArubaOS8.9.0.0

The following changes were introduced:

Theband parameter was introduced.

Replacedphy-typewithbandin the command output parameter.

ArubaOS8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms.

Base operating system.

Enable or Config mode on themanaged deviceorcontrollerwhere the AP terminates.