show ap arm client-match probe-report

ap-name

ip-addr

ip6-addr

assoc

phy-type 802.11a|802.11b|80211g

Description

If ClientMatch is enabled, the output of this command displays the client probe report for the specified AP. APs using ClientMatch maintain a table of clients that have sent probe requests, and the signal-to-noise ratio (SNR) of the frame the AP received from the client. The AP sends these reports to themanaged device每30秒,managed deviceforwards this information to theMobility Conductor, which uses the information in these reports to steer each client to its optimal AP.

Parameter	Description
ap-name	Name of the AP for which you want to view a client report.
ip-addr	IPv4 address of an AP for which you want to view a client probe report.
ip6-addr	IPv6 address of an AP for which you want to view a client probe report.
assoc	Show information for associated clients only.
phy-type	Show information for one of the following phy types: 802.11a 802.11b 80211g

Example

(host)#show ap arm client-match probe-report ap-name

AP Client Probe Report for Wifi0

--------------------------------

Client MAC Signal Assoc Sec since Sec since Last heard

last heard last reported

---------- ------ ----- ------------ ---------- ----------

00:24:d7:40:ca:88 15 0 49 10 Wed Apr 10 01:20:46 2013

00:26:c6:4d:2b:74 21 0 23 10 Wed Apr 10 01:21:12 2013

00:1e:65:2b:7a:3e 23 0 55 10 Wed Apr 10 01:20:40 2013

74:e5:43:4b:3b:ff 34 0 20 10 Wed Apr 10 01:21:15 2013

AP Client Probe Report for Wifi1

--------------------------------

Client MAC Signal Assoc Sec since Sec since Last heard

last heard last reported

---------- ------ ----- ------------ -------------- ----------

22:33:44:55:66:77 50 0 6 9 Wed Apr 10 01:21:29 2013

c8:f7:33:29:82:db 41 0 60 9 Wed Apr 10 01:20:35 2013

ac:81:12:59:5c:12 32 0 50 9 Wed Apr 10 01:20:45 2013

00:24:d7:40:bb:b0 31 0 58 9 Wed Apr 10 01:20:37 2013

00:1a:73:15:8c:5f 32 0 57 9 Wed Apr 10 01:20:38 2013

The output of this command includes the following parameters:

Column	Description
Client MAC	AP name of the AP from which the client can detect a signal.
Signal	信号圣rength, in dBm, of the probe request received from the client.
Assoc	A "Y" in this field indicates that the client is currently associated to that AP radio.
Sec since last heard	Time elapsed since the AP radio heard from the client.
Sec since last reported	Time elapsed since the AP radio heard from the client.
Last heard	Date and time at which the AP last heard from the client

Related Commands

Command	Description
rf arm-profile	This command enables ClientMatch.
show ap arm client-match neighbors	This command displays the BSSID of other APs seen by clients in the select AP's RF neighborhood.
show ap arm virtual-beacon-report	This command displays the virtual beacon report for an AP with a specific IP or MAC address.
show ap arm client-match unsupported	This command displays a list of clients that failed to be steered to a more optimal AP, and the reason the initial steering request was triggered.
show ap arm client-match summary	This command shows the history of AP association changes triggered by the client match feature.
show ap arm client-match history	This command shows the history of AP association changes triggered by the client match feature.
show ap arm client-match restriction-table	This command displays the list of clients that ClientMatch has restricted from the specified AP.

Command History

Release	Modification
ArubaOS8.0.0.0	Command introduced.

Command Information

Platforms	许可证	Command Mode
All platforms	Base operating system.	Enable or Config mode onMobility Conductor.